Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.

Watco Easy Marking Tape

Incredibly strong tape designed to make line marking easy

  • Won't curl or tear
  • Virtually permanent adhesive
  • Easily cut before application
  • Interior and exterior use
Frequently bought together


This new material is designed to make line marking as easy as possible! 


  • High specification adhesive lets you reposition the tape without leaving a mark. Once cured (about 24 hours) the adhesive is virtually permanent
  • Waxed backing paper allows you to cut pieces to size before sticking them into place
  • Non-curling, tear-resistant, vinyl material
  • 160 micron thickness and strong colours for clearer markings
  • Can be used externally–we recommend you prime poor or porous surfaces beforehand using Watco Safety Tape Primer


Properties Self adhesive, easy application, waxed backing allows you to cut pieces to size before sticking them into place, tear-resistant, strong colours.
Surfaces Floors.
Interior or Exterior Interior and exterior.
Primer required Yes, for dusty or porous surfaces.
Coverage 30m per roll.
Width (mm) 50
Roll length (m) 30


Surface preparation

Concrete - Concrete to be treated must be at least four weeks old, completely dry and free of surface laitance (a weak dusty layer on concrete), contaminants and any previous poorly bonded coatings. All traces of grease or oil should be removed with Watco Bio D (or similar degreasant) and the area thoroughly washed off and allowed to dry. Very smooth concrete or concrete with surface laitance should be etched with Watco Etch & Clean to ensure adequate adhesion. The concrete should be thoroughly washed down and allowed to dry after treatment with Watco Etch & Clean.

Stone - Stone should be dry and free of all loose surface material and contaminants.

Painted Surfaces - Previously painted surfaces should be thoroughly abraded by sanding to improve adhesion and to remove any weak or loose material. A trial area is advisable to test compatability with previous coatings.

Bare Metal - Remove any rust and flaking material by disc grinding or wire brushing. Apply the coating immediately after preparation to the clean metal surface. Grease or oil can be removed using Watco Bio D a solvent free degreaser. Allow the metal to dry before coating.

Galvanised Metal - Do not apply the coating direct to galvanised metal surfaces without first preparing using Watco Galvaprime. Watco Galvaprime is a single pack wash primer for use on galvanised surfaces prior to the application of Watco Safety Grip. Surfaces treated with Watco Galvaprime should be allowed to dry before coating.


Pour the liquid contents of the two small tins (resin and hardener) into the larger outer tin and mix thoroughly until uniform in colour. Do not mix in the anti-slip aggregate.

The mixed components must be decanted into a shallow roller tray and used immediately. If the mixed components are not decanted the mixing tin will quickly become very hot and could pose a hazard.


If appearance is critical we recommend the application of a small trial area first.

A pile-type roller (not foam) should be used to apply the mixed resin and hardener. Pour the mixed resin and hardener into a shallow roller tray. It is recommended that the product be applied in the following manner:

  • Apply the mixed resin and hardener by roller to a measured area of 5m
  • Immediately sprinkle the anti-slip aggregate uniformally onto the wet coat to obtain the desired surface finish (total or light coverage)
  • Using the same roller that was used to apply the mixed resin and hardener roll over the sprinkled aggregate to bed in and cover the anti-slip aggregate

It is not normally necessary to re-charge the roller with mixed resin unless very heavy quantities of grit have been applied.

In exceptional temperature conditions advice should be obtained from Watco’s Technical Department.

Case studies

Case studies

Ask a question


Be the first to ask a question...

Ask a question
0 questions / 0 answers

€31.45 (Ex VAT)

In stock

Recently Viewed

Watco Easy Marking Tape

Watco Easy Marking Tape

Incredibly strong tape designed to make line marking easy

From €31.45  (Ex VAT)