Seals and waterproofs metal or concrete bund areas and pipes. Excellent chemical resistance
Watco Bund Sealer is a two part, thick epoxy resin, one coat is generally enough to achieve a waterproof seal that is highly chemical resistant. New easier to apply formula with glass reinforcement for even greater resistance to chemical attack.
| Properties | New, easier to apply' formula, can be applied to damp surfaces, excellent resistance to petrol, diesel, acids, alkalis and solvents, fills cracks between bund wall and floor. |
| Finish | Glossy, smooth |
| Surfaces | Floors or walls. |
| Interior or Exterior | Interior and exterior |
| Primer required | No. |
| Composition | 2 part, 100% solids epoxy resin |
| Coverage | 14m² per 4L |
| Number of coats | 1 |
| Recommended number of coats | 1 |
| Pot time (hours) | Up to 25 minutes at 20°C. |
| Dry film thickness | 300 microns |
| Curing time | 12 hours at 20°C |
| Minimum application temperature | 10°C |
Ensure surfaces are clean, sound and free of contaminants. Large cracks in the surface should be repaired prior to Application of Watco Bund Sealer. Minor cracks and joints can be bridged by Bund Sealer with Watco Fibreglass Reinforcing Tape. Remove grease and oil using Watco Bio D.
Watco Bund Sealer can be applied to damp surfaces, although for more permanent installations we recommend that the surface is as dry as possible. Watco Bund Sealer can be applied to painted surfaces but all loose or defective paint should be removed first. Remove loose rust from metal (it is not necessary to remove all ‘well bonded’ rust). Heavily corroded, very rusty metal can be primed with Watco Primebase.
Add the contents of the 2 inner tins to the outer tin. Part Mixing is not recommended. Using a flat bladed palette-knife or similar tool, scrape all the material from the inside of the tins and mix thoroughly.
If appearance is critical we recommend the Application of a small trial area first.
Apply by brush, working well into the substrate. The product can be brushed thickly over hairline cracks and joints. One coat is generally sufficient to produce a watertight seal. A second coat may be required on very porous surfaces or to produce a continuous film over rough surfaces.
|
|
|
|
|
|---|---|---|---|---|
|
This product:
Watco Bund Sealer |
Watco Chemi-Coat |
Watco Chemi-Coat Anti Slip |
Watco Chemi-Coat Acid Strength |
|
|
From €243.15 (Ex VAT) |
From €228.55 (Ex VAT) |
From €236.00 (Ex VAT) |
From €258.85 (Ex VAT) |
|
|
Please make a product selection to continue |
View | View | View | |
| Composition | 2 part, 100% solids epoxy resin | 2 part, 100% solids epoxy resin | 2 part, 100% solids epoxy resin | 2 part, 100% solids epoxy resin |
| Durability | Very heavy | Very heavy | Very heavy | Very heavy |
| Anti Slip | ||||
| Chemical Resistant | Excellent | Excellent | Excellent | Excellent plus |
| Interior or Exterior | Interior and exterior | Interior | Interior | Interior |
| Finish | Glossy, smooth | Glossy, smooth | Glossy, textured | Glossy, smooth |
| Number of coats | 1 | 1 | 1 | 1 |
|
Please make a product selection to continue |
View | View | View |
Strengthens and waterproofs joints and cracks in bund areas
€44.70 (Ex VAT)
Seals and waterproofs metal or concrete bund areas and pipes. Excellent chemical resistance
From €243.15 (Ex VAT)
