Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.

Watco Protecta-Coat Anti Slip

For warehouses, walk-in fridges, exterior car parks. Exceptionally durable two-pack resin

  • Two pack polyaspartic resin formula
  • Excellent slip resistant finish
  • Highly durable and chemical resistant
  • Can be applied at temperatures as low as -10°C
Frequently bought together


Watco Protecta-Coat Anti Slip is an exceptionally hard wearing two-pack resin coating, which will protect your floors for the long term. It cures to a smart mid-gloss finish to enhance the look of your premises. All you need to do is ensure the area to be coated is clean, dry and free from grease.

Recommended areas of use

  • Warehouses
  • Showrooms
  • Walk-in fridges
  • Exterior car parking areas


  • Protects coloured and decorative coatings from heavy wear and tear
  • Can be applied at temperatures ranging from -10°C to +30°C
  • Excellent chemical resistance, thus enhancing workplace safety
  • Suitable for internal and external use
  • Watco Protecta-Coat Anti Slip has a finely textured slip resistant finish
  • Externally it will resist chalking, fading, weathering and has exceptional resistance to UV


Properties A two pack product which cures to a smart mid-gloss finish
Suitable for Concrete, painted floors
Finish Clear, medium texture
Interior or Exterior Exterior, Interior
Composition 2 part polyaspartic resin
Coverage 30m² per 2.5L
Number of coats 1
Recommended number of coats 1
Dry film thickness 100 microns
Curing time (at 20°C) 6 hours
Minimum application temperature -10°C
Maximum application temperature 30°C



Protecta-Coat can be used over most existing paint coatings, although a sample area should be tested first if in doubt. Protecta-Coat will also cope with slight movement in an existing coating, and is therefore fine to overcoat asphalt coatings and areas around vibrating machinery for instance.

Surface preparation

Floor temperature must be above -10°C and dry. Floor temperature must be above -10°C and dry. Previously painted surfaces should be diamond grinded thoroughly prior to application to achieve a consistently rough profile, and ensure all weakly bonded material is removed. Glossy or inadequately prepared surfaces may cause adhesion issues, so a thorough inspection is recommended to ensure no areas are missed, a bristle blaster can be used in any hard-to-reach areas. Thoroughly sweep the area following grinding; any loose material or dust can compromise adhesion. Bio-D can be used to remove any grease and oil from the surface following the grinding process, however, surfaces washed with Watco Bio D must be then thoroughly rinsed with water and allowed to dry fully, prior to coating.

 A trial area is advisable to test compatibility with previous coatings. If applying outside do not apply when rain is forecast.


Mix between 10°C-25°C. Remove the two tins from the large outer tin. Stir each tin individually and pour into larger outer tin. (Ensure that tin contents are completely emptied by scraping the sides etc). Mix the components together thoroughly using a spatula or wide bladed tool. Continue mixing until an even blend/consistency is obtained. Do not mix more than one tin at a time. If a Watco Mixing Blade and electric drill are used, also use a spatula to ensure any unmixed material from sides/corners and bottom of the tin is not missed. Do not dilute. The product will last for 25-30 minutes at 15°C. Less at higher temperatures.


Apply between -10°C and +30°C. The viscosity will become somewhat thicker when applied at temperatures below 0°C and may result in a slight loss of coverage. When mixed a short pile roller should be used to work the product to around or over a 30m² area. This product is designed and performs best when applied very thinly (50 microns). If applied too thickly curing problems can occur.

Curing times

Times are dependent on site conditions, but the following can be used as a guide:

Recoatable4-5 hrs10-12 hrs16 hrs30 hrs
Light Traffic6-8 hrs18 hrs24 hrs36 hrs
Heavy Traffic12 hrs24 hrs36 hrs48 hrs
Ask a question


Be the first to ask a question...

Ask a question
0 questions / 0 answers

€170.75 (Ex VAT)

In stock

Do you know the size of the area?

Tools and accessories

What our customers say

Watco Protecta-Coat Anti Slip