Your browser version is not officially supported, and you may experience a degraded service. Please upgrade your browser.

Watco Powerfloat Sealer Anti Slip

Special formulation for smooth, power floated concrete floors with an anti slip finish

  • Apply direct to power floated or smooth, non-porous concrete
  • No need for expensive mechanical floor preparation
  • Excellent slip resistance
  • Tough, easy clean epoxy resin formulation
Frequently bought together


Watco Powerfloat Sealer Anti Slip is specially designed for very smooth, hard, power floated concrete floors. Such surfaces should usually be shotblasted or ground to provide a key, but this unique epoxy resin formulation can be simply applied by roller directly to the smooth surface. Removing the need for blasting or texturing means the attractive smooth surface of the concrete is maintained and costly shotblasting work is avoided.

Recommended areas of use

  • Powerfloated or very smooth concrete


  • Available in 2 finishes: gloss anti slip and matt anti slip
  • One coat seals, dustproofs and protects
  • Quicker to seal: no grinding or shotblasting needed before coating
  • Provides an anti slip surface


Properties Two pack epoxy resin supplied as a 5L unit.
Suitable for Power floated or very smooth concrete
Finish Clear, fine textured
Surfaces Concrete floors
Interior or Exterior Interior
Primer required No
Composition 2 part, water based epoxy resin
Coverage Approximately 40m² per 5L per coat
Number of coats 1
Recommended number of coats Usually 1. Two coats may be required to produce an even finish if the substrate has some porosity
Application tools Medium pile roller. Cut in using a brush.
Dry film thickness 100 microns
Curing time 16 hours at 15°C
Minimum application temperature 15°C
Pot life 2 hours at 20°C
Storage Between 15°C-25°C for at least 8 hours prior to use. Do not allow to freeze


Surface preparation

New concrete should be allowed at least 28 days to dry. Surfaces should be clean, dry and free from oil, grease, dust, dirt and other contaminants. Existing coatings should be well bonded and sound.


The tall outer tin contains a tin of Resin and a tin of Curing Agent. Remove these two tins and stir the contents of each thoroughly. Decant both tins into the tall outer tin. The two components should then be very thoroughly mixed together using a wide bladed stirrer. A wooden batten at least 25mm wide is ideal. Mix for 2-3 minutes until an even consistency is obtained. Both liquids are opaque white/off white in colour and it is important to ensure complete Mixing to allow the cure reaction to happen.


Decant the mixed components into a roller tray and apply using a medium pile type roller. A brush may be used for cutting in. Important – apply to a well ventilated area of no less than 40m2 . If this product is applied too thickly and/or the area is not sufficiently ventilated to allow a ‘through’ draught, it could fail to dry from white to clear. Aim to apply the mixed components within one hour (they are useable for up to 2 hours maximum at 20°C). Do not apply at temperatures below 10°C or above 30°C. Cold or damp conditions may retard or prevent full curing. The two components for Powerfloat Sealer and Powerfloat Sealer Anti Slip are white, but the coating will cure to a clear finish within 2 hours

Ask a question


Be the first to ask a question...

Ask a question
0 questions / 0 answers

€125.55 (Ex VAT)

In stock

Do you know the size of the area?

Tools and accessories

Watco Etch & Clean

Watco Etch & Clean

Essential for preparing bare concrete ready for painting

€34.67  (Ex VAT)

12" Roller Frame & Handle

12" Roller Frame & Handle

A sturdy roller perfect for applying floor and wall coatings

From €9.63  (Ex VAT)

What our customers say

Recently Viewed

Watco Powerfloat Sealer Anti Slip

Watco Powerfloat Sealer Anti Slip

Special formulation for smooth, power floated concrete floors with an anti slip finish

From €125.55  (Ex VAT)