For loading bays, walkways and entrances incl wet, oil and heavily trafficked areas. Cures at 0°C
| Quantity | Price per item | Discount |
|---|---|---|
| 1+ | €162.35 | - |
| 6+ | €146.10 | Save 10% |
| Bulk discounts applied in basket | ||
Total price
€313.85 (Ex VAT)
Watco Safety Grip Cold Cure is a heavy duty, coarse textured, anti slip, two pack epoxy resin coatings designed to provide a safe surface both inside and out. Using one high build coat of Safety Grip minimises the risk of accidents throughout the workplace, particularly for wet or oily areas. All grades now carry CE Mark EN 1504-2 and have test results for slip resistance, abrasion, scratch and impact resistance, as well as for adhesion and hardness. They are also chemical resistant and have an A+ VOC emissions rating with a low level of VOC.
Watco Safety Grip Cold Cure can be applied as low as 0°C, providing exceptional slip resistance in unheated areas or outside in the winter months.
* Please note, if the colour light grey is required for an external application, please use Safety Grip Flex Light Grey, this product is better suited for UV resistance.
| Temperature | Recoat Time | Touch Dry | Light Traffic | Heavy Traffic | |
| Safety Grip | 10°C 20°C 30°C | 16 hours 12 hours 8 hours | 12 hours 6 hours 4 hours | 24 hours 16 hours 12 hours | 36 hours 24 hours 24 hours |
| Safety Grip Rapid | 10°C 20°C 30°C | 12 hours 8 hours 6 hours | 8 hours 4 hours 3 hours | 16 hours 8 hours 8 hours | 36 hours 24 hours 24 hours |
| Safety Grip Cold Cure | 0°C 10°C 20°C | 20 hours 12 hours 10 hours | 12 hours 8 hours 6 hours | 24 hours 16 hours 16 hours | 48 hours 36 hours 24 hours |
| Safety Grip Flex | 10°C 20°C 30°C | 12 hours 8 hours 6 hours | 10 hours 6 hours 3 hours | 16 hours 12 hours 12 hours | 24 hours 24 hours 24 hours |
Full Chemical Resistance: 7 days Light Traffic: foot, trolley, pallet truck, occasional forklift Heavy Traffic: regular forklift, heavy footfall, parked vehicles | |||||
| Suitable for | Concrete well bonded paint, most flat rigid metals and stone |
| Finish | Heavily textured, glossy |
| Interior or Exterior | Exterior, Interior |
| Primer required | Not usually. See ‘Priming’ section in 'Application' |
| Composition | Anti slip, 100% solids epoxy resin |
| Number of components | 1 x curing agent, 1 x resin and 1 x anti slip particles |
| Coverage | 5m² per unit |
| Number of coats | 1 |
| Recommended number of coats | 1 |
| Application tools | Medium pile roller. Cut using a brush |
| Dry film thickness | 320 microns |
| Curing time (at 0°C) | 24 hours |
| Minimum application temperature | 0°C |
| Pot life | Up to 30 minutes at 20°C |
| Storage | Between 15°C - 25°C for at least 8 hours prior to use. Do not allow to freeze |
| Shelf life | 24 months in unopened container |
| Cleaning | Normal industrial cleaners - Watco bio D is ideal. Do not steam clean |
| Cleaning tools | It is not practical to clean applicators and they should be discarded after use |
Bare Concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow the surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.
New Concrete – as a guide, new concrete should be left for 8 weeks to dry. The surface should then be prepared using Watco Etch & Clean, thoroughly rinsed and left to dry.
Priming – is not usually required, but for very porous high suction surfaces, such as sand and cement screed, use Watco 4 Hour Epoxy Primer. Concrete should be sufficiently porous to allow the paint to penetrate, so very smooth or power floated concrete is unsuitable unless first primed with Watco Powerfloat Primer.
Painted Surfaces – abrade to remove any weak or loose paint. Check remaining paint is well bonded. Very smooth, glossy paint should be lightly abraded to provide a key. Watco Bio D can be used to remove grease and oil from painted surfaces. Watco Concroff is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint). A trial area is advisable to test compatibility with previous coatings.
Asphalt – new asphalt must be sound and at least 3 months old. If any residual oils remain, the surface should be washed using Watco Concroff. Painted asphalt should be cleaned with Watco Bio D (Concroff can soften paint), and a trial area is advisable to test compatibility with previous coatings.
Metal – remove any rust and flaking material by disc grinding or wire brushing. Apply the coating immediately after preparation to the clean metal surface. Grease or oil can be removed using Watco Bio D. Allow the metal to dry before coating.
Galvanised Metal – Watco Galvaprime must be used to prepare galvanised metal.
Non-ferrous Metals – for advice, please contact our Technical Department.
Remove dirt with a medium stiff broom or light scrubbing machine using detergents if necessary - Watco Bio D is ideal.
Extensive testing is what makes us the most highly qualified paint and repair manufacturer on the market. Our tests cover just about everything you might want to know about a floor coating – how well it bonds to the floor, how durable it is, how well it stands up to scratching and much more.
Our key tests for Safety Grip:
Learn more about the tests we carry out and how to read the results here.
Full test results can be found on the Technical Data Sheet.
| Quantity | Price per item | Discount |
|---|---|---|
| 1+ | €162.35 | - |
| 6+ | €146.10 | Save 10% |
| Bulk discounts applied in basket | ||
