A single pack, general use anti slip concrete floor paint. Pre-blended for uniform finish
|Quantity||Price per item||Discount|
|Bulk discounts applied in basket|
Our unique formula is based on a blend of resins and polyurethane, which produced a ‘Best in Class’ single pack paint for general use. This attractive, hardwearing coating is easy to apply and dries quickly to provide a low maintenance, tough, oil resistant finish. Watco Concrete Floor Paint Anti Slip provides a good level of slip resistance and the anti slip particles are pre-blended which makes it easier to achieve a uniform finish.
All grades now carry CE Mark EN 1504-2 and have impressive test results for abrasion, scratch and impact resistance, as well as for adhesion, hardness and flexibility. All tests have been undertaken to ISO standard where applicable, and demonstrated this ‘Best Ever Formulation’ to be four times more scratch resistant than previously, twice as hard wearing and with 50% improved adhesion.
|Curing Times||Recoat Time||Touch Dry||Light Traffic||Full Use|
|10°C||24 hours||16 hours||48 hours||72 hours|
|20°C||16 hours||10 hours||24 hours||36 hours|
|30°C||16 hours||6 hour||24 hours||36 hours|
|Light Traffic: Foot, trolley, pallet truck, occasional forklift|
|Suitable for||Concrete, wood, most metals, existing well bonded paint|
|Finish||Glossy, fine textured|
|Interior or Exterior||Interior|
|Primer required||Not usually. See ‘Priming’ section in 'How to Apply'.|
|Composition||Single pack, solvent based polyurethane|
|Number of components||1|
|Coverage||40m² per 5L per coat|
|Number of coats||2|
|Wet film thickness||120 microns.|
|Dry film thickness||80 microns|
|Curing time||24 hours at 20°C|
|Minimum application temperature||10°C|
|Shelf life||12 months in unopened containers.|
|Cleaning tools||White Spirit.|
Bare Concrete – remove surface laitance, dust and any light dirt or grease deposits using Watco Etch & Clean. Watco Etch & Clean also etches smooth, bare concrete surfaces to provide a key. Flush with clean water and allow surface to dry. For the removal of heavier deposits of oil and grease we recommend Watco Concroff, again, flush with clean water and allow the surface to dry.
New Concrete – as a guide, new concrete should be left for four weeks to dry in the summer and six in the winter. The surface should then be prepared using Watco Etch & Clean and thoroughly rinsed away and left to dry prior to applying this coating.
Priming – is not usually required, but for very porous high suction surfaces, such as sand and cement screed, use Watco 4 Hour Epoxy Primer. Concrete should be sufficiently porous to allow the paint to penetrate, so very smooth or power floated concrete is unsuitable unless first primed with Watco Powerfloat Primer.
Painted Surfaces – abrade to remove any weak or loose paint. Check remaining paint is well bonded. Very smooth, glossy paint should be lightly abraded to provide a key. Watco Bio D can be used to remove grease and oil from painted surfaces. Watco Concroff is a very powerful degreaser for contaminated bare concrete, (do not use on a previously painted surface since it can soften paint).
The paint should be thoroughly stirred and must not be thinned. Apply by roller and work well into the surface. Use a paint brush for edges. Avoid applying the paint too thickly. The second coat can be applied as soon as the first coat is dry (generally 16 hours), and should be applied within 5 days. If more than 5 days elapse, the first coat should be lightly abraded before the second coat is applied. Avoid washing the surface for 7 days.
Chemical resistance is important for areas that store or use chemicals. To protect the surface and increase its longevity, you’ll need a coating that stands strong against chemical spills.All chemical resistance
Painting your floor isn't an easy task, so getting the right level of durability will increase the longevity of your floor. In choosing a hardwearing product, you won't need to revisit the project for years.Shop paint
Conventional floor paints need to be applied above 10°c in order for them to cure. We’ve formulated products using the latest resin technology, so you can apply them temperatures down to -10°c.All cold cure
A sturdy roller perfect for applying floor and wall coatings
From €9.63 (Ex VAT)