General use anti slip floor paint. Mix in aggregate for a glossy, easy to clean finish
Watco Basics Floor Paint is based on a tough solvent based polyurethane formula which makes it ideal for general use. It can be applied over existing well bonded paint, or onto bare concrete, making cleaning easier. A separate unit of aggregate is supplied with Anti Slip Floor Paint, which is mixed into the paint to provide a finely textured slip resistant surface. For heavier wear areas, or areas where vehicles will be parked, we recommend Anti Slip Epoxy Resin Floor Paint to resist ‘picking’ under parked car tyres.
Suitable for | Concrete, wood, most metals, existing well bonded paint |
Finish | Glossy, anti slip |
Interior or Exterior | Interior |
Composition | Single pack, solvent based polyurethane |
Number of components | 1 |
Coverage | 40m² per 5L per coat |
Number of coats | 2 |
Recommended number of coats | 2 |
Dry film thickness | 80 microns |
Curing time (at 20°C) | 24 hours |
Minimum application temperature | 10°C |
Storage | Avoid extremes of temperature |
Shelf life | 36 months in unopened container |
Cleaning tools | Clean tools with White Spirit |
Clean and prepare bare concrete using Watco Etch and Clean or Watco Bio-D. This will remove grease and oil deposits from existing paint.
If over coating existing paint, please ensure it is well bonded. Remove any flaking or poorly bonded paint using a floor scraper for smaller areas or hire a grinder for larger areas. Smooth, glossy paint should be lightly abraded to provide a key.
Make sure the surface is clean and dust free before continuing.
Bare concrete must be porous to allow the first coat of paint to penetrate and key. If in doubt pour a small amount of water on the floor. If it soaks in, the concrete can be painted. If it beads up because the concrete is very smooth and dense, perhaps power floated, do not proceed, but refer instead to Watco Powerfloat Primer.
New concrete should be at least 2 months old and the Watco Bio-D used to reduce alkalinity.
Holes in excess of 5mm deep can be filled with Watco Basics Floor Repair Mortar, or providing the floor is level, Watco Pourable Repair Mortar.
For repairs which need to be ‘feather edged’ to nothing, or for repairs to damaged joint edges, please refer to Watco Concrex epoxy resin repair mortar. This should also be used if repairing broken kerb edges or step nosings.
Check the air temperature is around 15°C and the floor temperature at least 10°C.
The surface must be dry.
Stir the paint thoroughly.
If using the Anti Slip Floor Paint, add the whole tin of aggregate to the 5L paint size, or half the tin to the 2.5L. Stir the aggregate thoroughly into the paint.
Apply using a roller. Do not apply thickly.
Use the roller to work the paint into the surface of bare concrete.
A brush can be used for cutting in around the edges.
Avoid applying in cold (below 15°C) conditions, instead see Watco Cold Set Coating.
Do not use in areas where vehicles are parked, instead see Watco Basics Epoxy Resin Floor Paint, or Watco Epoxy Gloss Coat Best Ever Formula.
In areas of chemical spillage, please refer to Watco Chemi Coat.
Unsuitable for outside application, instead use Watco Fastcoat.
Do not use in very slippery, wet, oily areas, instead see Watco Safety Grip.
|
|
|
|
|
---|---|---|---|---|
This product:
Watco Basics Anti Slip Floor Paint |
Watco Basics Floor Paint |
Epoxy Resin Floor Paint |
Watco Epoxy Gloss Coat |
|
From €50.75 (Ex VAT) |
From €43.30 (Ex VAT) |
From €58.25 (Ex VAT) |
From €177.30 (Ex VAT) |
|
Please make a product selection to continue |
View | View | View | |
Composition | Single pack, solvent based polyurethane | Single pack, solvent based polyurethane | 2 part, water based epoxy resin | 2 part reinforced water based epoxy resin |
Durability | Light-medium | Light-medium | Medium | Heavy |
Anti Slip | ||||
Chemical Resistant | Limited | Limited | Good | Good |
Suitable for parked cars | ||||
Finish | Glossy, anti slip | Glossy, smooth | Mid gloss, smooth | Glossy, smooth |
Recommended number of coats | 2 | 2 | 2 | 2 |
Please make a product selection to continue |
View | View | View |
Painting your floor isn't an easy task, so getting the right level of durability will increase the longevity of your floor. In choosing a hardwearing product, you won't need to revisit the project for years.
Shop paintIf you are looking for an attractive smooth finish than you will find it here at Watco. We dont just specialise in Anti Slip, but high performance smooth coatings to.
Shop paintChemical resistance is important for areas that store or use chemicals. To protect the surface and increase its longevity, you’ll need a coating that stands strong against chemical spills.
All chemical resistanceConventional floor paints need to be applied above 10°c in order for them to cure. We’ve formulated products using the latest resin technology, so you can apply them temperatures down to -10°c.
All cold cureTake the stress out of painting your floor with our rapid curing products. You can clean, prepare and paint your floors in as little as just one day.
All rapidA matt finish helps to reduce the amount of glare on the surface. So, imperfections such as dents and scratches will be disguised. Giving you the perfect floor finish you are after.
Shop paint